How much does it cost to build an RC plane from scratch?

Many kits come with poor quality hardware that should probably be replaced. These "not included" parts are covered by your $400. If you build your first plane, which I strongly recommend that you do, you will probably spend in the neighborhood of $100 on basic tools, glues and a small building board of some type .

What electronics do I need to build an RC plane?

Thanks hobbyking! Step 1: Transmitters. The transmitter is what you use to control your plane with. ... Step 2: Receivers. ... Step 3: ESC (Electronic Speed Controller) ... Step 4: Battery. ... Step 5: Motor. ... Step 6: Servos. ... Step 7: Soldering. ... Step 8: Connecting It All Up! More items...

What is the easiest RC plane to build?

Park Flyers . Park flyers are great for beginners because they are simple to put together, tough, and forgiving to fly. They're lightweight, perfect for flying in smaller areas like local parks, and come with lots of helpful instructions to make learning easier.

Is it illegal to fly an RC plane?

RC hobbyists are considered “recreational users” by the FAA. Specific rules apply to us, intended to ensure public safety in the increasingly busy skies. For example, RC hobby aircraft are not allowed near airports, over stadiums and sporting events, and in security-sensitive areas .

What electronics do I need to build a RC car?

You'll need most of them during the assembly process, however, so get them before you start to build. The required electronics will include a radio transmitter, receiver, and servos . For most RC car kits, a basic two- or three-channel surface radio system will do, such as the Spektrum SLT3 or DX3.

Can you build an RC plane from scratch?

There are two ways: you make the whole fuselage on your own, or you can buy fuselage and only add electronic parts to it . The first way is much harder but you can design any RC plane you want.

How much would it cost to build your own plane?

How much does it cost, realistically, to build an airplane? There's no absolute answer, of course, but homebuilt airplanes can be, and consistently are, completed for $50,000 to $65,000 . Many cost considerably less, and of course, there's no upper limit. Building an airplane is a pay-as-you-go proposition.

Is it legal to build a plane from scratch?

A custom built aircraft requires a pilot license to fly in addition to an airworthiness certificate for the airplane . An ultralight does not require a pilot's license or an airworthiness certificate - generally speaking. Basically, there are five different types of materials used in building amateur-built airplanes.

What is the cost of making a plane?

General Aviation Airplanes: $100,000 – $1,000,000 . Small Private Jets / Single-Engine Turboprops: $1 million – $10 million. Large Private Jets / Regional Jets: $10 million – $80 million. Commercial Airliners: $80 million – over $200 million.

The Very Best In RC Electronics, Hardware & Laser Cut Kits! (2024)

Home |2024 DAYTON MODELRAMA | View Shopping Cart

Shop

3D Printing

Adhesives/CA/Epoxy

Chargers

Composites / Carbon Rod

E-Power Everything

Gears

Gift Certificates

Hardware

Kits

Multi-Rotor Copters

Onboard Electronics

Orbit Specialty Items

Rad Wear

Radio Sets

Radio Plugs, Wire, Etc.

Scale Accessories

Simulator

Software

Wood/Foams/Materials

Z-Rack-N-Stack Hanger

Rod Stock Policy Items

Custom Charges

Discontinued || Selling Out

One Of A Kind

Radical Specials

Til It's Gone!

Refurbished Equipment

Page [ 1 | 2 ]

Featured Category:Refurbished Equipment
Opportunities to save some serious moolah...

The Savox SC-0251MG is a high torque, metal-geared, digital servo which is suitable for many applications.

Features:

Metal gear train ensures durability under harsh situations.
Slightly taller case design.
Ideal for aircraft and some 1/8 off road car applications.

Specifications:

Torque @ 4.8v - 13.0kg/180.5oz-in
Torque @ 6v - 16.0kg/222.2oz-in
Speed @ 4.8v - 0.20 sec/60 deg
Speed @ 6v - 0.18 sec/60 deg
Dimensions L x W x H (mm): 40.7 x 19.6 x 42.4
Weight: 61.0g
Operating Temperature: 14° - 122°F (-10° - 50°C) Running Current (no load): 300mA @4.8V, 350mA @6.0V
Stall Current (at locked): 2600mA @4.8V, 3200mA @6.0V
Idle Current: 5mA @4.8V, 6mA @6.0V
Wire Length: 300 +/- 5mm
Output Gear Spline: 25 Tooth
Bearings: 2BB
Operating Travel: 120? (1000 -> 2000 μ second)
Neutral Position: 1500 u second
Pulse Width Range: 800 -> 2200 μ second
Maximum Travel: Appx 164? (800 -> 2200 μ second)
Refresh Rate: 240 Hz
Motor Type: Brushed

Discontinued, while supplies last! 3 LEFT IN STOCK

See SAVSC-0251MGP for replacement

SKU Number: SAVSC-0251MG

The Savox SC-0252MG is a high torque, metal-geared, digital, standard servo. A great replacement for standard, plastic-geared servos with less torque.

Features:

Metal gear train ensures durability under harsh situations.
Higher torque output than standard servos.
Ideal for 30-60 size aircraft, and some car applications.

Specifications:

Torque @ 4.8v - 7.2kg/100.0oz-in
Torque @ 6v - 10.5kg/145.8oz-in
Speed @ 4.8v - 0.23 sec/60 deg
Speed @ 6v - 0.19 sec/60 deg
Dimensions L x W x H (mm): 40.7 x 19.6 x 39.4
Weight: 49.0g
Operating Temperature: 14° - 122°F (-10° - 50°C)
Running Current (no load): 300mA @4.8V, 330mA @6.0V
Stall Current (at locked): 1400mA @4.8V, 1700mA @6.0V
Idle Current: 6mA @4.8V, 6mA @6.0V
Wire Length: 300 +/- 5mm
Output Gear Spline: 25 Tooth
Bearings: 2BB
Operating Travel: 120° (1000 -> 2000 μ second)
Neutral Position: 1500 μ second
Pulse Width Range: 800 -> 2200 μ second
Maximum Travel: Appx 164° (800 -> 2200 μ second)
Refresh Rate: 240 Hz
Motor Type: Brushed

Discontinued, last one!

See SAVSC-0252MGP for replacement

SKU Number: SAVSC-0252MG

The SC-0253MG is a budget friendly, digital standard servo with metal gears and a bearing support for those wanting more than what a standard servo offers.

Features:

Strong metal gear train for added durability.
Ideal for 1/10 cars and planes.
Great replacement for standard servos with plastic gearing.

Specifications:

Torque @ 4.8v - 4kg/55.0oz-in
Torque @ 6v -6.0kg/83.3oz-in
Speed @ 4.8v - 0.17 sec/60 deg
Speed @ 6v - 0.15 sec/60 deg
Dimensions L x W x H (mm): 40.7 x 20.0 x 37.0
Weight: 59.0g
Operating Temperature: 14° - 122°F (-10° - 50°C)
Running Current (no load): 220mA @4.8V, 240mA @6.0V
Stall Current (at locked): 800mA @4.8 V, 1000mA @6.0V
Idle Current: 5mA @4.8V, 5mA @6.0V
Wire Length: 250 +- 5mm
Output Gear Spline: 25 Tooth
Bearings: 2BB
Operating Travel: 120° (1000 -> 2000 μ second)
Neutral Position: 1500 μ second
Pulse Width Range: 800 -> 2200 u second
Maximum Travel: Appx 164° (800 -> 2200 μ second)
Refresh Rate: 240 Hz
Motor Type: Brushed

SKU Number: SAVSC-0253MG

The SC-1252MG is a high speed, low profile servo which combines leading edge technology with super high 12 bit (4096) resolution. Ideal for 1/10 on-road cars where space is limited and speed is desired.

Features:

Metal gear train ensures durability under harsh situations.
Ideal for 1/10 on road vehicles.
Aluminum case provides cooler operating temperatures.

Specifications:

Torque @ 4.8v - 4.5kg/62.5oz-in
Torque @ 6v - 7.0kg/97.2oz-in
Speed @ 4.8v - 0.08 sec/60 deg
Speed @ 6v - 0.07 sec/60 deg
Dimensions L x W x H (mm): 40.8 x 20.2 x 25.4
Weight: 44.5g
Operating Temperature: 14° - 122°F (-10° - 50°C)
Running Current (no load): 150mA @4.8V, 180mA @6.0V
Stall Current (at locked): 2000mA @4.8V, 3000mA @6.0V
Idle Current: 5mA @4.8V, 5mA @6.0V
Wire Length: 300 +/- 5mm
Output Gear Spline: 25 Tooth
Bearings: 2BB
Operating Travel: 90° (1000 -> 2000 μ second)
Neutral Position: 1500 μ second
Pulse Width Range: 950 -> 2050 μ second
Maximum Travel: Appx 160° (700 -> 2300 μ second)
Refresh Rate: 240 Hz
Motor Type: Brushed

Discontinued, while supplies last, 2 LEFT IN STOCK!

See SAVSC-1252MGP for replacement

SKU Number: SAVSC-1252MG

Overview

Use of the sock is optional, though recommended. The sock will help prevent marking and potential creasing of the underlying airplane structure.

After installing the sock, place the iron on the included stand, then place it on a heat resistant surface. Connect the iron to an appropriate AC wall outlet. Press the ON/OFF button to power the iron on. Adjust the temperature to the desired level with the temperature adjustment buttons.

Holding both the ON/OFF and C/F button for approximately three seconds will change the temperature display mode between Celsius and Fahrenheit.

Set the iron to the temperature recommended for the covering material being used. Once the iron reaches the set temperature, it's ready for use. You may find it helpful to test a scrap piece of covering to ensure the temperature setting is appropriate for the task being performed. Often tacking the shrinking are performed at different temperatures.

Features

Precise digital temperature control
LCD power indicator
Adjustable temperature units
Perfect for any heat shrink film or fabric covering
Updated shoe design for easier covering
Teflon coated shoe prevents scratching
Metal stand and sock included
Ergonomic handle design for comfortable handling
Three-hour shutoff safety feature

See all soldering Tools: Tools - Sub - Soldering

SKU Number: HAN1017

INSTA-SET(TM) is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET(TM) in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET(TM) significantly enhances a joint's strength. For difficult to bond materials, INSTA-SET(TM) can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET(TM) is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.

USES:

All Cyanoacrylates

DIRECTIONS:

After joining parts with cyanoacrylate (CA, super glue), spray the seams with Insta-Set(TM) to cure the CA in 8 seconds. A bead of CA can then be applied to the outside and corners of joints before another application of Insta-Set(TM) to reinforce their strength. Insta-Set(TM) can also be applied to one part (with CA on the other) before joining for difficult to bond materials. Insta-Set(TM) is compatible with all surfaces, including clear plastic and all foams. It also is a great cleaning agent for adhesive residue and scuff marks. Store separately from CAs.

AVAILABLE SIZES:

BSI-151 (Pump Spray): 2 Fl. oz (60 ml)

BSI-155 (Aerosol): 6.75 Fl. oz. (200 ml)

BSI-152 (Refill): 8 Fl. oz. (240 ml)

MADE IN THE USA

SKU Number: BSI151

Ultra-Cure(TM) is a very high performance clear cyanoacrylate that has a viscosity (thickness) in-between that of Insta-Cure Super Thin and Insta-Cure+ Gap Filling Medium. It is ideal for the mounting of rubber tires onto R/C car wheels. It is available in our 3/4 oz Pocket CA bottle and comes with one of our new #304 Extender Tips for the Pocket CA pin-in-cap top. ULTRA-CURE(TM) can be used in many other applications that require a slightly thicker thin CA and will bond virtually everything. It is not foam-safe, however.

USES:

R/C rubber tires

DIRECTIONS:

Unscrew top from nozzle. For finer applications, use the extender tip. Carefully lift the sidewall of the tire after it is mounted to the wheel to expose the area to be bonded. Apply a drop of Ultra-Cure(TM)CA Tire Glue into the gap, then slowly return the tire to its seated position. Continue this process around the circumference of the tire. Repeat these steps for the other side. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life when not in use. Ultra-Cure(TM)is also superior for bonding most other materials. Soak extender tip in acetone for cleaning.

AVAILABLE SIZES:

BSI-130: 3/4 oz (20.3 g)

BSI-129: 1 oz (28.4 g)

MADE IN THE USA

SKU Number: BSI130

Insta-Cure+(TM) is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ (TM) should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. Works Best On:

Balsa Wood
Soft Wood

Works Good On:

Hard Wood
Glass & Metal
Fiberglass
Ceramics
Hard Plastics
Rubber
Laminating
Water-Resistant
Reinforcing

DIRECTIONS:

Unscrew top from nozzle. For finer applications, use the extender tip. Apply Insta-Cure+(TM) CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set(TM) accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40° to 220° F. Soak extender tip in acetone for cleaning.

AVAILABLE SIZES:

BSI-106: 1/2 oz (14.2 g)

BSI-107: 1 oz. (28.4 g)

BSI-108: 2 oz. (56.8 g)

BSI-109: 8 oz. (227 g)

MADE IN THE USA

SKU Number: BSI106

Maxi-Cure(TM) extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE(TM) is the best choice for plastic model assembly. When used with INSTA-SET(TM), it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE(TM) bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, cloth textured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE(TM) or any other adhesive. It also is best for bonding the tires for R/C cars. MAXI-CURE(TM) has proven to be very popular in the archery business for the fletching of vanes onto aluminum and carbon arrow shafts. Along with being the strongest, MAXI-CURE(TM) is usually the least expensive option for this application. Works Best On:

Soft Wood
Hard Wood
Glass & Metal
Fiberglass
Ceramics
Hard Plastics Rubber
Laminating
Reinforcing

Works Good On:

Balsa Wood
Water-Resistant

DIRECTIONS:

Unscrew top from nozzle. For finer applications, use the extender tip. Apply Maxi-Cure(TM) CA to one side of the parts being joined, then hold them tightly to- gether for 10-20 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set(TM) accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220? F. Soak extender tip in acetone for cleaning.

AVAILABLE SIZES:

BSI-111: 1/2 oz (14.2 g)

BSI-112: 1 oz. (28.4 g)

BSI-113: 2 oz. (56.8 g)

BSI-114: 8 oz. (227 g)

MADE IN THE USA

SKU Number: BSI111

Plastic-Cure(TM) is a gap-filling formulation of CA that works best on plastics. It is packaged in a bottle with a brush built into its top, which in many cases is an easier way to apply the CA. As long as brush is put back into the bottle after use, the bristles of the brush will not harden. Care must be taken, however, not to introduce foreign material into the bottle. The brush should not be used, for example, to apply CA to wood that has been freshly sanded. Plastic-Cure will also bond wood, but its brush applicator at times will not be the best way to apply it. Plastic-Cure is superior for the application of false nails and wraps on fingernails, where its brush is the preferred method of application.

USES:

Plastics
Wood
Foam
False nails and wraps on fingernails

DIRECTIONS:

Carefully unscrew the cap. Brush on Plastic-Cure(TM) to one surface of the parts being joined, then hold parts tightly together for 10-20 seconds. Plastic-Cure(TM) won't frost clear plastic and works on white foam. Insta-Set(TM) Accelerator must be used when bonding two pieces of foam together. Full strength is reached in 3 hours. Excess cured adhesive can be removed by rubbing the area with a paper towel soaked in Un-Cure(TM). Refrigerate to extend shelf life. Cured CA is stable from -40° to 220° F.

AVAILABLE SIZE:

1/2 oz (14.2 g)

MADE IN THE USA

SKU Number: BSI105

Insta-Cure(TM) has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. Works Best On:

Balsa Wood
Ceramics

Works Good On:

Soft Wood
Fiberglass &
Hard Plastics
Water-Resistant
CA Hinges

DIRECTIONS:

Unscrew top from nozzle. For finer applications, use the extender tip. Insta-Cure(TM) CA is used to bond tight fitting parts. Hold the parts together (sometimes using masking tape), then apply the Insta-Cure(TM) along the joints. The CA will penetrate deep into the joints. Bonding will occur in 1-3 seconds. Excess cured CA can be removed from surfaces like ceramics by rubbing with a paper towel soaked in Un-Cure(TM). Full strength is reached in two hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40° to 220° F. Soak extender tip in acetone for cleaning.

AVAILABLE SIZES:

BSI-101: 1/2 oz (14.2 g)

BSI-102: 1 oz. (28.4 g)

BSI-103: 2 oz. (56.8 g)

BSI-104: 8 oz. (227 g)

MADE IN THE USA

SKU Number: BSI101

Insta-Flex(TM) flexible thin CA is ideal for many applications, including the installation of CA hinges. When cured, INSTA-FLEX(TM) does not turn brittle and remains clear, even if accelerated with INSTA-SET(TM). It has superior shock resistance. Although not as thin in consistency as INSTA-CURE(TM), INSTA-FLEX(TM) still has good penetrating qualities and its application can be easier to control. For CA hinges, we recommend drilling a 1/16" hole in the center of the hinge slots to insure the complete saturation of the hinge when INSTA-FLEX(TM) is applied. INSTA-FLEX(TM) has a different, less irritating odor compared to regular CA's, but still cannot be used on white foam. INSTA-FLEX(TM) has also proven to be superior when bonding anodized aluminum.

Works Best On:

Balsa Wood
Glass & Metal
Rubber CA Hinges

Works Good On:

Soft Wood
Hard Wood
Fiberglass
Ceramics
Hard Plastics
Laminating
Water-Resistant
Reinforcing

DIRECTIONS:

Sorry for the inconvience. This information will be coming soon.

AVAILABLE SIZE:

BSI-119: 1 oz. (28.4 g)

MADE IN THE USA

SKU Number: BSI119

Insta-Flex+(TM) clear rubber toughened has similar qualities to our black IC-2000(TM) but can be used in applications where you do not want the adhesive to be seen. The carbon component of IC-2000(TM) that gives the CA its black color also contributes to its unsurpassed strength. Since INSTA-FLEX+(TM) has this carbon removed, its strength is a little less than IC-2000(TM) but still superior to standard CA's. When esthetics are important and a flexible bond is required, INSTA-FLEX+(TM) is your best choice. It forms superior bonds to soft urethane and vinyl plastics. Both INSTA-FLEX(TM) and INSTA-FLEX+(TM) work well when bonding R/C car tires. When a joint has a larger than normal gap, flexible CA's provide superior shock resistant bonds.

Works Best On:

Hard Wood
Glass & Metal
Fiberglass
Hard Plastics
Rubber

Works Good On:

Balsa Wood
Soft Wood
Ceramics
Laminating
Water-Resistant
Reinforcing

DIRECTIONS:

Sorry for the inconvenience. This information will be coming soon.

AVAILABLE SIZE:

BSI-120: 1 oz. (28.4 g)

MADE IN THE USA

SKU Number: BSI120

IC-2000(TM) is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. For model use, IC-2000(TM) is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 20-40 seconds, which can be accelerated with INSTA-SET(TM). When cured, IC-2000(TM) is pliable enough to be carved with a hobby knife. IC-2000(TM) is the best adhesive for R/C car tires.

IC-2000(TM) has found many uses in industrial applications, such as rubber to rubber bonding by Beechcraft, carbon composite bonding by Boeing, rubber door seals by Volkswagen, speaker and subwoofer assembly in the audio industry and many others that need the most durable, shock resistant fast bonding adhesive that is available.

Works Best On:

Glass & Metal
Fiberglass
Hard Plastics
Rubber
Reinforcing

Works Good On:

Balsa Wood
Soft Wood
Hard Wood
Ceramics
Laminating
Water-Resistant

DIRECTIONS:

Screw on top and cap unit to puncture the seal on the tube Remove cap and apply IC-2000(TM) CA to one side of the parts being joined, then hold them tightly together for 10-25 seconds for shock resistant joints. For larger bonding areas, apply serpentine beads of the CA, allowing for the spreading of the adhesive. For maximum flexibility, do not use with an accelerator. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40° to 250° F. Top and tip can be soaked in acetone for cleaning.

AVAILABLE SIZE:

BSI-117: 1/2 oz (14.2 g)

BSI-118: 1 oz. (28.4 g)

MADE IN THE USA

SKU Number: BSI117

BSI's IC-2000(TM) black rubber and carbon toughened Cyanoacrylate is recognized as being the strongest instant glue for non-porous surfaces. Its enhanced shock resistance, strength, and fast bonding make it ideal for use on rubber components, such as Beechcraft's King Air executive transports. IC-2000(TM) has found a home in golf club and speaker repair shops, carbon composite bonding by Boeing, rubber door seals by Volkswagen, carbon composites used in aerospace, and many others that need the most durable, shock resistant fast bonding adhesive that is available.

Works Best On:

Glass & Metal
Fiberglass
Hard Plastics
Rubber
Reinforcing

Works Good On:

Balsa Wood
Soft Wood
Hard Wood
Ceramics
Laminating
Water-Resistant

DIRECTIONS:

Screw on top and cap unit to puncture the seal on the tube. Remove cap and apply IC-2000(TM) CA to one side of the parts being joined, then hold them tightly together for 10-25 seconds for shock resistant joints. For larger bonding areas, apply serpentine beads of the CA, allowing for the spreading of the adhesive. For maximum flexibility, do not use with an accelerator. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 250? F. Top and tip can be soaked in acetone for cleaning.

AVAILABLE SIZE:

BSI-117H: .7 oz. (20 g)

MADE IN THE USA

SKU Number: BSI117H

FOAM-CURE(TM) is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it's curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE(TM) can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE(TM) will act like a contact cement when the parts are rejoined, resulting in enough tack strength to allow the next steps of assembly. Full strength is reached in 10-12 hours. FOAM-CURE(TM) works with all foams and will actually bond most other materials. It will bond wood and plastic to foam and is a good canopy glue. FOAM-CURE(TM) does not, however, cure flexible enough to act as a hinge for aircraft control surfaces. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE(TM) requires exposure to air for drying. If one tried to bond, for example, a half-dollar coin to glass, over 90% of the adhesive would never cure, since the solvent it contains would have nowhere to evaporate. A small amount of denatured alcohol can be mixed into the Foam-Cure to make it thinner.

Works Best On:

EPP Foam
EOP Foam
Clear Canopy
Paper and Crafts

DIRECTIONS:

Cut off tip of nozzle. Apply to one part before joining. Use tape to hold parts in place during cure. For faster curing, pull the joint apart and let Foam-Cure(TM) air dry for 5-10 min before rejoining the parts. This results in enough tack strength to allow the next steps of assembly. Full cure takes 10-12 hours. Foam-Cure(TM) works on all foams, especially on EPP and EPO, and will bond a porous surface to non-porous materials. Foam-Cure(TM) is also an excellent glue for clear canopies, and will also bond paper. If needed, denatured alcohol can be used to thin or clean up uncured Foam-Cure(TM). Replace cap after use.

AVAILABLE SIZE:

BSI-141: 1 Fl. oz (30 ml)

BSI-142: 4 Fl. oz. (120 ml)

MADE IN THE USA

SKU Number: BSI141

SLOW-CURE(TM) 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE(TM) can be used for bonding if you're willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE(TM) and FINISH-CURE(TM) to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength within 24 hours.

Works Best On:

Glass & Metal
Fiberglass
White Foam
Water-Resistant
Reinforcing

Works Good On:

Balsa Wood
Soft Wood
Hard Wood
Hard Plastics
Laminating

DIRECTIONS:

SLOW-CURE(TM) 30 min. Epoxy is an equal two-part hobby adhesive that forms high strength bonds through a chemical reaction between the resin and hardener. The cured epoxy is resistant to most chemicals.

SLOW-CURE(TM) has the highest strength of our epoxies and should be applied in temperatures above 70°F. SLOW-CURE(TM) maintains its strength in both the lowest and highest temperature ranges of our line of epoxies.

SLOW-CURE(TM) bonds best to clean, textured surfaces. Smooth, non-porous surfaces should be roughened with coarse sandpaper to improve adhesion. Acetone and Isopropyl rubbing alcohol work as the best solvents for cleaning uncured epoxy from surfaces. SLOW-CURE(TM) works best for forming reinforcing fillets on joints and can be mixed with micro balloons or other fillers to form putty-like consistency. SLOW-CURE(TM) is waterproof and forms superior bonds if you're willing to wait overnight. It has better penetration of porous surfaces for better bonding. Full cure in 6-8 hours.

AVAILABLE SIZE:

BSI-205: 4.5 oz combined net wt. (128 g)

BSI-206: 9 oz combined net wt. (256 g)

MADE IN THE USA

SKU Number: BSI205

QUIK-CURE(TM) 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress.

QUIK-CURE(TM) shouldn't be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats.

QUIKCURE(TM) is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE(TM) can be handled after 15 minutes. Full strength is reached in 1 hour.

Works Best On:

Hard Wood
Glass & Metal

Works Good On:

Balsa Wood
Soft Wood
Fiberglass
Ceramics
Hard Plastics
White Foam
Reinforcing

DIRECTIONS:

QUIK-CURE(TM) 5 min. Epoxy is an equal two-part hobby adhesive that forms high strength bonds through a chemical reaction between the resin and hardener. The cured epoxy is resistant to most chemicals.

QUIK-CURE(TM) is the least temperature sensitive of our epoxies. It will cure in temperatures down to 40°F. Temperatures above 90°F shorten the working time before the epoxy begins to set up from 5 to less than 4 minutes.

QUIK-CURE(TM) bonds best to clean, textured surfaces. Smooth, non-porous surfaces should be roughened with coarse sandpaper to improve adhesion. Acetone and Isopropyl rubbing alcohol work as the best solvents for cleaning uncured epoxy from surfaces. QUIK-CURE'S(TM) lack of brittleness allows it to form lasting bonds on materials as different as balsa wood and glass; however, it is not recommended for areas subject to long-term immersion in water. Cured QUIK-CURE(TM) can be coated with polyester resin without affecting the curing of the resin. Full cure in less than 15 minutes.

AVAILABLE SIZE:

BSI-201: 4.5 oz combined net wt. (128 g)
BSI-202: 9 oz combined net wt. (256 g)

MADE IN THE USA

SKU Number: BSI201

MID-CURE(TM) 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE(TM) in most applications.

MID-CURE(TM) is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.

Works Best On:

Hard Wood
Fiberglass

Works Good On:

Balsa Wood
Soft Wood
Glass & Metal
Hard Plastics
Rubber
White Foam
Laminating
Water-Resistant
Reinforcing

DIRECTIONS:

MID-CURE(TM) 15 min. Epoxy is an equal two-part hobby adhesive that forms high strength bonds through a chemical reaction between the resin and hardener. The cured epoxy is resistant to most chemicals.

MID-CURE(TM) should be applied in temperatures above 65?F. It can be used in most applications when you need more working time than QUIK-CURE(TM) provides. MID-CURE(TM) can be worked for about 10 minutes, with adhesion beginning after about 15 minutes.

MID-CURE(TM) bonds best to clean, textured surfaces. Smooth, non-porous surfaces should be roughened with coarse sandpaper to improve adhesion. Acetone and Isopropyl rubbing alcohol work as the best solvents for cleaning uncured epoxy from surfaces. MID-CURE(TM) is our most flexible epoxy. This gives it superior bonding qualities in applications such as hardwood to fiberglass. MID-CURE'S(TM) lack of brittleness allows it to form lasting bonds in areas subject to high vibration or stress. MID-CURE(TM) is a water-resistant substitute for QUIK-CURE(TM). Full cure in 2-3 hours.

AVAILABLE SIZE:

BSI-203: 4.5 oz combined net wt. (128 g)
BSI-204: 9 oz combined net wt. (256 g)

MADE IN THE USA

SKU Number: BSI203

Pocket CAs are available in 3/4 & 4 oz. sizes and feature a top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. This pin also helps prevent the clogging of the nozzle. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. BSI's #304 extender tip can be used on the nozzle for finer applications. The Pocket CAs are available with BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+.

AVAILABLE SIZES:

Insta-Cure(TM) Super Thin BSI-131: 3/4 oz (20.3 g)

Insta-Cure(TM) Super Thin BSI-132: 4 oz (113.4 g)

Insta-Cure+(TM) Gap Filling BSI-133: 3/4 oz (20.3 g)

Maxi-Cure(TM) Extra Thick BSI-135: 3/4 oz (20.3 g)

Super-Gold+(TM) Gap Filling BSI-139: 3/4 oz (20.3 g)

IC-Gel(TM) CA Gel BSI-116: .7 oz (20 g)

MADE IN THE USA

SKU Number: BSI131

Works on all surfaces, including: glass, cardboard, plastic, fiberglass and everything else. INSTA-CLEAN(TM) is ideal for removing price stickers and their adhesive residue. INSTA-CLEAN(TM) will also remove scuff marks that regular household cleaners won't touch.

Works Good On:

Stickers
Sticker Residue
Residue on Glass
Residue on Fiberglass

DIRECTIONS:

Spray directly onto the sticker to be removed. Let stand for 1 to 5 minutes and then peel off sticker and wipe clean.

AVAILABLE SIZES:

BSI-100H: 2 FL. oz. (59 ml)

MADE IN THE USA

SKU Number: BSI100H

Hitec's X2 charger is similar to the X4 except 200 watts charging power per port is allowed. Charges Lipo/Lion/Life(A123) packs up to 6S, PB (lead acid) up to 10S and NiCad/NiMH packs up to 15 cells. Both ports run completely independently from each other. Maximum 10 amps charge current, 5 amps discharge current. Power up your larger packs more quickly with this charger.

Input Voltage: DC 11-18V up 30A (depending on charge settings)
Input Connectors: 4mm banana plug with 12 AWG wire
Charging Current: 0.1~10.0A (max 200W, total 400W)
Discharging Current: 0.1~5.0A (max 25W, total 50W)
Balance Connector Type: JST-XH, Poly Quest, Hyperion
Size: 8.2 x 5.3 x 2.2" (200 x 135 x 57mm)
Weight: 1.6lbs (727g)

DISCONTINUED BY HITEC, WHILE SUPPLIES LAST!

SALE!

SKU Number: HRC44164

With the Cobra Brushless Aircraft Speed Controllers, three of the programming options can be changed with the throttle stick on your transmitter. To be able to program all of the features available on the Cobra Speed Controllers, the Cobra ESC Programming Card is required.

NOTE: The Cobra Programming Card is only for use with the Aircraft Versions of Cobra Speed Controllers. These can easily be identified by a green stripe down the center of the label and have part numbers that start with "DL". This program card does not work with the Cobra Multirotor Speed Controllers. These can easily be identified by an all-black label, and part numbers that start with "MR".

The Programming Card is very easy to use, you simply set the six programming jumpers to the desired settings and plug the programming card into the control lead on your ESC. Then, with a motor connected to the ESC, plug in the motor battery and wait a couple seconds. After you hear the confirmation tone, unplug the battery and the programming is complete! To complete the process, unplug the Programming Card for the ESC, and plug the control lead back into the throttle channel on your radio receiver.

With the Cobra ESC Programming Card, you can access all of the programming features available in the speed controller. These features include:

Battery Type: Three different types of battery chemistry are supported, Li-Po/Li-Ion, Ni-Cad/Ni-MH and Li-Fe/A123. (The default setting is Li-Po/Li-Ion cells)
Cut-off Voltage Level: For each battery chemistry there are three different Low Voltage cut-off levels available, High, Medium and low. For Li-Po/Li-Ion cells 3.2, 3.0 or 2.8 volts per cell can be selected. For NiCad/Ni-MH cells 0.9, 0.8 or 0.6 volts per cell can be selected. For Li-Fe/A123 cells, 2.8, 2.5 or 2.2 volts per cell can be selected. (The default setting is the Medium setting for each battery chemistry)
LVC Cut-off Type: When the selected Low Voltage level is reached, the ESC can be set to provide either a Hard Cut-off or a Power Reduction Mode. (The default setting is Power Reduction Mode)
Brake Level: The Brake Level can be set to one of three levels. Hard Brake, which is used with folding type props, Medium Brake, which is used with normal props or Off, if the user desires to have the prop free-wheel when the ESC is in the idle condition. (The Default setting is Medium Brake level)

Timing Mode: The ESC Timing can be set to one of three values, Auto to let the ESC determine the best setting for the motor that it is driving, High to get maximum power and performance from high pole count outrunner motors or Low for economic performance and use with low pole count outrunners or inrunner type motors. (The default setting is Auto Timing)
Motor Acceleration Rate: The Motor Acceleration Rate can be set to one of three values. High is for use in planes where immediate throttle response is desired, such as 3D type aircraft. Medium is for normal sport flying to get smooth throttle transitions when power changes are made. Low is for models with very large props, or motors that are used in gearbox applications to prevent high power pulses that could strip out the gears. (The default setting is Medium Acceleration rate)

SKU Number: C-ESC-PROG

Cobra Speed Controllers are designed with a relentless pursuit of exceptional product quality. These speed controllers are the perfect complement to a Cobra Brushless motor, and they will also work with virtually any other brushless motor on the market as well. Cobra Speed Controllers are built from the best components available to provide the user with long life and trouble-free operation.

Cobra Speed Controllers are simple to program, and in most cases, they can be used right out of the package. Three of the Speed Controller parameters can be set without a programming card: Brake Mode, Battery Type, and Timing mode. The remaining parameters can be set with the optional ESC Programming Card, which is available separately.

All of the Cobra Speed Controllers come with an internal BEC circuit to power your radio receiver and servos. This 150A model comes with a 5.5 volt switching BEC rated for 6 amps of current to handle the power needs of the larger digital servos.

Because of the wide range of different motor connectors used on this size speed controller, the Cobra 100A ESC comes without any bullet connectors already installed. The motor leads are pre-tinned and ready to solder on your favorite connectors. 5mm or larger bullet connectors are recommended for this size speed controller.

Cobra Speed Controller Features

Easy Set-up and Operation
Basic Programming available through Throttle Stick
Throttle Range automatically detected and set for smooth, linear throttle response
Three different types of Low Voltage Cut-off available for Li-Po, Ni-XX or LiFe batteries
Three different LVC levels for each cell type: 3.2, 3.0 or 2.8 Volts/cell for Li-Po batteries, 0.9, 0.8 or 0.6 Volts/cell for Ni-XX batteries and 2.8, 2.5 or 2.2 Volts/cell for Li-Fe batteries
LVC type can be set to Hard Cut-off or Power Reduction Mode
Three different brake levels, Hard, Medium or Off
Three different timing modes, High, Low and Auto
Three different Motor Acceleration Rates, High, Medium and Low
Safe Start-Up: The ESC will not arm until the throttle is in the idle position
Locked-Rotor Protection: If the motor is blocked so the prop cannot rotate, the ESC will automatically shut down to prevent damage
PWM Frequency is set to 8KHz for best operation on a wide range of motors
Over Temp Protection: Shuts down the ESC output if temperature exceeds 230F (110C)
Auto Power Cut-off: If the throttle signal is lost for more than 3 seconds, the throttle will reduce to idle to prevent fly-aways.

Cobra 150 Amp ESC Specifications:

Weight (Without Connectors):82.0 grams (2.8 oz)

Max Continuous Current: 150 Amps

Burst Current rating (15s): 188 Amps

Operating Voltage Range: 6 to 26 Volts

Number of Li-Po cells: 2 to 6 cells

Number of Ni-XX cells: 6 to 20 cells

Number of Li-Fe cells: 2 to 7 cells

Switching BEC Output: 6 amps @ 5.5 Volts

ESC Size (Inc. Caps, in mm): 72 x 33 x 18

ESC Size (Inc. Caps, in inches): 2.83 x 1.30 x 0.71

Note: The Cobra speed controllers do NOT ship with the programming card. This part must be purchased separately. The same programming card is used for the entire series of Cobra speed controllers so only one programming card is needed for all of your Cobra speed controllers.

SKU Number: C-150A-ESC

All of the Cobra Speed Controllers come with an internal BEC circuit to power your radio receiver and servos. This 100A model comes with a 5.5 volt switching BEC rated for 6 amps of current to handle the power needs of the larger digital servos.

Because of the wide range of different motor connectors used on this size speed controller, the Cobra 100A ESC comes without any bullet connectors already installed. The motor leads are pre-tinned and ready to solder on your favorite connectors. 4mm or larger bullet connectors are recommended for this size speed controller.

Cobra Speed Controller Features

Easy Set-up and Operation
Basic Programming available through Throttle Stick
Throttle Range automatically detected and set for smooth, linear throttle response
Three different types of Low Voltage Cut-off available for Li-Po, Ni-XX or LiFe batteries
Three different LVC levels for each cell type: 3.2, 3.0 or 2.8 Volts/cell for Li-Po batteries, 0.9, 0.8 or 0.6 Volts/cell for Ni-XX batteries and 2.8, 2.5 or 2.2 Volts/cell for Li-Fe batteries
LVC type can be set to Hard Cut-off or Power Reduction Mode
Three different brake levels, Hard, Medium or Off
Three different timing modes, High, Low and Auto
Three different Motor Acceleration Rates, High, Medium and Low
Safe Start-Up: The ESC will not arm until the throttle is in the idle position
Locked-Rotor Protection: If the motor is blocked so the prop cannot rotate, the ESC will automatically shut down to prevent damage
PWM Frequency is set to 8KHz for best operation on a wide range of motors
Over Temp Protection: Shuts down the ESC output if temperature exceeds 230F (110C)
Auto Power Cut-off: If the throttle signal is lost for more than 3 seconds, the throttle will reduce to idle to prevent fly-aways.

Cobra 100 Amp ESC Specifications:

Weight (Without Connectors): 69.8 grams (2.46 oz)

Max Continuous Current: 100 Amps

Burst Current rating (15s): 125 Amps

Operating Voltage Range: 6 to 26 Volts

Number of Li-Po cells: 2 to 6 cells

Number of Ni-XX cells: 6 to 20 cells

Number of Li-Fe cells: 2 to 7 cells

Switching BEC Output: 6 amps @ 5.5 Volts

ESC Size (Inc. Caps, in mm): 72 x 33 x 14

ESC Size (Inc. Caps, in inches): 2.83 x 1.30 x 0.55

SKU Number: C-100A-ESC

All of the Cobra Speed Controllers come with an internal BEC circuit to power your radio receiver and servos. This 80A model comes with a 5.5 volt switching BEC rated for 6 amps of current to handle the power needs of the larger digital servos.

Because of the wide range of different motor connectors used on this size speed controller, the Cobra 80A ESC comes without any bullet connectors already installed. The motor leads are pre-tinned and ready to solder on your favorite connectors. 4mm or larger bullet connectors are recommended for this size speed controller.

Cobra Speed Controller Features:

Easy Set-up and Operation
Basic Programming available through Throttle Stick
Throttle Range automatically detected and set for smooth, linear throttle response
Three different types of Low Voltage Cut-off available for Li-Po, Ni-XX or LiFe batteries
Three different LVC levels for each cell type: 3.2, 3.0 or 2.8 Volts/cell for Li-Po batteries, 0.9, 0.8 or 0.6 Volts/cell for Ni-XX batteries and 2.8, 2.5 or 2.2 Volts/cell for Li-Fe batteries
LVC type can be set to Hard Cut-off or Power Reduction Mode
Three different brake levels, Hard, Medium or Off
Three different timing modes, High, Low and Auto
Three different Motor Acceleration Rates, High, Medium and Low
Safe Start-Up: The ESC will not arm until the throttle is in the idle position
Locked-Rotor Protection: If the motor is blocked so the prop cannot rotate, the ESC will automatically shut down to prevent damage
PWM Frequency is set to 8KHz for best operation on a wide range of motors
Over Temp Protection: Shuts down the ESC output if temperature exceeds 230F (110C)
Auto Power Cut-off: If the throttle signal is lost for more than 3 seconds, the throttle will reduce to idle to prevent fly-aways.

Cobra 80 Amp ESC Specifications:

Weight (Without Connectors): 60.1 grams (2.12 oz)

Max Continuous Current: 80 Amps

Burst Current rating (15s): 100 Amps

Operating Voltage Range: 6 to 26 Volts

Number of Li-Po cells: 2 to 6 cells

Number of Ni-XX cells: 6 to 20 cells

Number of Li-Fe cells: 2 to 7 cells

Switching BEC Output: 6 amps @ 5.5 Volts

ESC Size (Inc. Caps, in mm): 72 x 33 x 14

ESC Size (Inc. Caps, in inches): 2.83 x 1.30 x 0.55

SKU Number: C-80A-ESC

All of the Cobra Speed Controllers come with an internal BEC circuit to power your radio receiver and servos. This 60A model comes with a 5.5 volt switching BEC rated for 6 amps of current to handle the power needs of the larger digital servos.

The Cobra 60A ESC comes with a set of 3.5mm female bullet connectors already installed. These connectors match up with the ones provided on the Cobra Brushless motors as well as most other brands of brushless motors on the market today.

Note: The Cobra speed controllers do NOT ship with the programming card. This part must be purchased separately. The same programming card is used for the entire series of Cobra speed controllers so only one programming card is needed for all of your Cobra speed controllers.

Cobra Speed Controller Features

Easy Set-up and Operation
Basic Programming available through Throttle Stick
Throttle Range automatically detected and set for smooth, linear throttle response
Three different types of Low Voltage Cut-off available for Li-Po, Ni-XX or LiFe batteries
Three different LVC levels for each cell type: 3.2, 3.0 or 2.8 Volts/cell for Li-Po batteries, 0.9, 0.8 or 0.6 Volts/cell for Ni-XX batteries and 2.8, 2.5 or 2.2 Volts/cell for Li-Fe batteries
LVC type can be set to Hard Cut-off or Power Reduction Mode
Three different brake levels, Hard, Medium or Off
Three different timing modes, High, Low and Auto
Three different Motor Acceleration Rates, High, Medium and Low
Safe Start-Up: The ESC will not arm until the throttle is in the idle position
Locked-Rotor Protection: If the motor is blocked so the prop cannot rotate, the ESC will automatically shut down to prevent damage
PWM Frequency is set to 8KHz for best operation on a wide range of motors
Over Temp Protection: Shuts down the ESC output if temperature exceeds 230F (110C)
Auto Power Cut-off: If the throttle signal is lost for more than 3 seconds, the throttle will reduce to idle to prevent fly-aways.

Cobra 60 Amp ESC Specifications

Weight (Without Connectors): 60.1 grams (2.12 oz)

Max Continuous Current: 60 Amps

Burst Current rating (15s): 75 Amps

Operating Voltage Range: 6 to 26 Volts

Number of Li-Po cells: 2 to 6 cells

Number of Ni-XX cells: 6 to 20 cells

Number of Li-Fe cells: 2 to 7 cells

Switching BEC Output: 6 amps @ 5.5 Volts

ESC Size (Inc. Caps, in mm):67 x 33 x 14

ESC Size (Inc. Caps, in inches): 2.64 x 1.30 x 0.55

SKU Number: C-60A-ESC

Cobra Speed Controllers are built from the best components available to provide the user with long life and trouble-free operation. The perfect complement to a Cobra Brushless motor!

Cobra Speed Controllers are designed with a relentless pursuit of exceptional product quality. These speed controllers are the perfect compliment to a Cobra Brushless motor, and they will also work with virtually any other brushless motor on the market as well. Cobra Speed Controllers are built from the best components available to provide the user with long life and trouble-free operation.

All of the Cobra Speed Controllers come with an internal BEC circuit to power your radio receiver and servos. This 40A model comes with a 5.5 volt switching BEC rated for 6 amps of current to handle the power needs of the larger digital servos.

The Cobra 40A ESC comes with a set of 3.5mm female bullet connectors already installed. These connectors match up with the ones provided on the Cobra Brushless motors as well as most other brands of brushless motors on the market today.

Cobra Speed Controller Features

Easy Set-up and Operation
Basic Programming available through Throttle Stick
Throttle Range automatically detected and set for smooth, linear throttle response
Three different types of Low Voltage Cut-off available for Li-Po, Ni-XX or LiFe batteries
Three different LVC levels for each cell type: 3.2, 3.0 or 2.8 Volts/cell for Li-Po batteries, 0.9, 0.8 or 0.6 Volts/cell for Ni-XX batteries and 2.8, 2.5 or 2.2 Volts/cell for Li-Fe batteries
LVC type can be set to Hard Cut-off or Power Reduction Mode
Three different brake levels, Hard, Medium or Off
Three different timing modes, High, Low and Auto
Three different Motor Acceleration Rates, High, Medium and Low
Safe Start-Up: The ESC will not arm until the throttle is in the idle position
Locked-Rotor Protection: If the motor is blocked so the prop cannot rotate, the ESC will automatically shut down to prevent damage
PWM Frequency is set to 8KHz for best operation on a wide range of motors
Over Temp Protection: Shuts down the ESC output if temperature exceeds 230F (110C)
Auto Power Cut-off: If the throttle signal is lost for more than 3 seconds, the throttle will reduce to idle to prevent fly-aways.

Cobra 40 Amp ESC Specifications

Weight (Without Connectors):48.4 grams (1.71 oz)

Max Continuous Current:40 Amps

Burst Current rating (15s):50 Amps

Operating Voltage Range: 6 to 26 Volts

Number of Li-Po cells: 2 to 6 cells

Number of Ni-XX cells: 6 to 20 cells

Number of Li-Fe cells: 2 to 7 cells

Switching BEC Output: 6 amps @ 5.5 Volts

ESC Size (Inc. Caps, in mm):64 x 26 x 13

ESC Size (Inc. Caps, in inches): 2.52 x 1.02 x 0.51

SKU Number: C-40A-ESC

All of the Cobra Speed Controllers come with an internal BEC circuit to power your radio receiver and servos. This 33A model comes with a 5.5 volt switching type BEC rated for 3 amps of current.

The Cobra 33A ESC comes with a set of 3.5mm female bullet connectors already installed. These connectors match up with the ones provided on the Cobra Brushless motors as well as most other brands of brushless motors on the market today.

Note: The Cobra speed controllers do NOT ship with the programming card. This part must be purchased separately. The same programming card is used for the entire series of Cobra speed controllers so only one programming card is needed for all of your Cobra speed controllers.

Cobra Speed Controller Features

Easy Set-up and Operation
Basic Programming available through Throttle Stick
Throttle Range automatically detected and set for smooth, linear throttle response
Three different types of Low Voltage Cut-off available for Li-Po, Ni-XX or LiFe batteries
Three different LVC levels for each cell type: 3.2, 3.0 or 2.8 Volts/cell for Li-Po batteries, 0.9, 0.8 or 0.6 Volts/cell for Ni-XX batteries and 2.8, 2.5 or 2.2 Volts/cell for Li-Fe batteries
LVC type can be set to Hard Cut-off or Power Reduction Mode
Three different brake levels, Hard, Medium or Off
Three different timing modes, High, Low and Auto
Three different Motor Acceleration Rates, High, Medium and Low
Safe Start-Up: The ESC will not arm until the throttle is in the idle position
Locked-Rotor Protection: If the motor is blocked so the prop cannot rotate, the ESC will automatically shut down to prevent damage
PWM Frequency is set to 8KHz for best operation on a wide range of motors
Over Temp Protection: Shuts down the ESC output if temperature exceeds 230F (110C)
Auto Power Cut-off: If the throttle signal is lost for more than 3 seconds, the throttle will reduce to idle to prevent fly-aways.

Cobra 33 Amp ESC Specifications

Weight (Without Connectors):37.1 grams (1.31 oz)

Max Continuous Current:33 Amps

Burst Current rating (15s):41 Amps

Operating Voltage Range: 6 to 17 Volts

Number of Li-Po cells: 2 to 4 cells

Number of Ni-XX cells: 6 to 12 cells

Number of Li-Fe cells: 2 to 4 cells

Switching BEC Output:3 amps @ 5.5 Volts

ESC Size (Inc. Caps, in mm):56 x 25 x 10

ESC Size (Inc. Caps, in inches): 2.20 x 0.98 x 0.39

SKU Number: C-33A-ESC

All of the Cobra Speed Controllers come with an internal BEC circuit to power your radio receiver and servos. This 22A model comes with a 5.0 volt switching type BEC rated for 2 amps of current.

The Cobra 22A ESC comes with a set of 3.5mm female bullet connectors already installed. These connectors match up with the ones provided on the Cobra Brushless motors as well as most other brands of brushless motors on the market today.

Note: The Cobra speed controllers do NOT ship with the programming card. This part must be purchased separately. The same programming card is used for the entire series of Cobra speed controllers so only one programming card is needed for all of your Cobra speed controllers.

Cobra Speed Controller Features

Easy Set-up and Operation
Basic Programming available through Throttle Stick
Throttle Range automatically detected and set for smooth, linear throttle response
Three different types of Low Voltage Cut-off available for Li-Po, Ni-XX or LiFe batteries
Three different LVC levels for each cell type: 3.2, 3.0 or 2.8 Volts/cell for Li-Po batteries, 0.9, 0.8 or 0.6 Volts/cell for Ni-XX batteries and 2.8, 2.5 or 2.2 Volts/cell for Li-Fe batteries
LVC type can be set to Hard Cut-off or Power Reduction Mode
Three different brake levels, Hard, Medium or Off
Three different timing modes, High, Low and Auto
Three different Motor Acceleration Rates, High, Medium and Low
Safe Start-Up: The ESC will not arm until the throttle is in the idle position
Locked-Rotor Protection: If the motor is blocked so the prop cannot rotate, the ESC will automatically shut down to prevent damage
PWM Frequency is set to 8KHz for best operation on a wide range of motors
Over Temp Protection: Shuts down the ESC output if temperature exceeds 230F (110C)
Auto Power Cut-off: If the throttle signal is lost for more than 3 seconds, the throttle will reduce to idle to prevent fly-aways.

Cobra 22 Amp ESC Specifications

Weight (Without Connectors):24.2 grams (.85 oz)

Max Continuous Current:22 Amps

Burst Current rating (15s):28 Amps

Operating Voltage Range: 6 to 12 Volts

Number of Li-Po cells: 2 to 3 cells

Number of Ni-XX cells: 6 to 10 cells

Number of Li-Fe cells: 2 to 3 cells

Switching BEC Output:2 amps @ 5. Volts

ESC Size (Inc. Caps, in mm):44 x 24 x 10

ESC Size (Inc. Caps, in inches):1.73 x 0.94 x 0.39

SKU Number: C-22A-ESC

All of the Cobra Speed Controllers come with an internal BEC circuit to power your radio receiver and servos. The 11A and 22A models come with a 5.0 volt linear BEC rated for 2 amps of current.

Since the Cobra 11A ESC is typically used in smaller 2-cell powered indoor aircraft, where most users solder the motor directly to the ESC to save weight, no bullet connectors are provided on the motor output leads. The leads are provided pre-tinned ready to solder.

Note: The Cobra speed controllers do NOT ship with the programming card. This part must be purchased separately. The same programming card is used for the entire series of Cobra speed controllers so only one programming card is needed for all of your Cobra speed controllers.

Cobra Speed Controller Features

Easy Set-up and Operation
Basic Programming available through Throttle Stick
Throttle Range automatically detected and set for smooth, linear throttle response
Three different types of Low Voltage Cut-off available for Li-Po, Ni-XX or LiFe batteries
Three different LVC levels for each cell type: 3.2, 3.0 or 2.8 Volts/cell for Li-Po batteries, 0.9, 0.8 or 0.6 Volts/cell for Ni-XX batteries and 2.8, 2.5 or 2.2 Volts/cell for LiFe batteries
LVC type can be set to Hard Cut-off or Power Reduction Mode
Three different brake levels, Hard, Medium or Off
Three different timing modes, High, Low and Auto
Three different Motor Acceleration Rates, High, Medium and Low ? Safe Start-Up: The ESC will not arm until the throttle is in the idle position
Locked-Rotor Protection: If the motor is blocked so the prop cannot rotate, the ESC will automatically shut down to prevent damage
PWM Frequency is set to 8KHz for best operation on a wide range of motors
Over Temp Protection: Shuts down the ESC output if temperature exceeds 230F (110C)
Auto Power Cut-off: If the throttle signal is lost for more than 3 seconds, the throttle will reduce to idle to prevent fly-aways.

Cobra 11 Amp ESC Specifications

Weight (Without Connectors): 9.9 grams (0.35 oz)

Max Continuous Current: 11 Amps

Burst Current rating (15s) 14 Amps

Operating Voltage Range 6 to 12 Volts

Number of Li-Po cells 2 to 3 cells

Number of Ni-XX cells 6 to 10 cells

Number of Li-Fe cells 2 to 3 cells

Linear BEC Output 2 amps @ 5.0 Volts

ESC Size (Inc. Caps, in mm) 30 x 18 x 10

ESC Size (Inc. Caps, in inches) 1.18 x 0.71 x 0.39

SKU Number: C-11A-ESC

The FrSky Tandem X20 Series is a dual-band telemetry radio system, its development has drawn on valuable feedback from FrSky's extensive customer base, experience with previous radios.

The Tandem series introduces many new features such as a color touch screen display, underpinned by an ergonomic design that provides unprecedented comfort when held.

On the RF side, FrSky has introduced a powerful and reliable TD dual-band RF system, which features the advantages of the FrSky 900MHz and 2.4GHz in one combined RF system. The TD dual-band RF system is characterized by true simultaneous dual-band remote control with telemetry, and superb end-to-end 4ms latency performance. When combined with ETHOS, a completely new operating system, FrSky's Tandem X20 Series provides users with a powerful, intuitive, and flexible experience to enjoy across the entire world of RC.

With the optional IRX4 4-N-1 module, the Tandem X20S will work with a variety existing RC ptotocal including: Spektrum DMS2 & DMSX, Futaba S-FHSS and others.

The Tandem X20S comes in three faceplate colors: Red, Blue and Black. Please specify color in the comment section. Also,the x20S includes: carring case, gimbal protectors, rubber covers for switches and Neck Strap

SPECIFICATIONS:

Dimension: 212*200*95 mm (L*W*H)
Weight: 809g (without battery)
Operating system: ETHOS
Internal RF module: TANDEM
Number of Channels: Up to 24 channels
Operating Voltage Range: 6.5 ~ 8.4V (2S Li-battery)
Operating Temperature: -10?C~60?C(14?F~140?F)
Operating Current: 240mA@7.4V (typ.)
Charging Current: <=1A ?200mA
USB Adaptor Voltage: 5V+0.2V
USB Adaptor Current: >2.0A
Backlit touchable LCD resolution: 800*480
Compatibility: ACCST D16 & ACCESS & TD receivers

SKU Number: FRS03010136

24" wing span electric RC model. This is our briefcase model! Park, sport & fun flyer with retro looks. Yes it really will fit inside a briefcase when you take the plug-in wings and tail surfaces (one nylon screw) off!

Wing Span: 24"

Overall length: 20"

Wing Area: 188 sq. in.

Weight: 10 oz

Wing loading: 7.6 oz per sq. ft.

Requires Outrunner Motor, Battery, 2S LiPo 900 mAhr

She has several unique features as well as good looks...

- The two wing panels plug in

- The tail group is attached by one nylon bolt. Removing the bolt allows the tail to be removed and packed flat for transport.

Optional extra long wing kit coming soon: Adds 48 sq. in. to the already large wing area. With the big wing she is a real floater with a wing loading of only 6.1 oz per sq. ft.

TEMPORARILY OUT OF STOCK

SKU Number: RRCBM

10-Pack of M3 large Quick Link Steel Clevis ends for 3mm threaded rods.
SKU Number: RRCM3QLSC10PK

ULTRA-HIGH POWER LITHIUM-ION CELL

INR21700-P45B

Molicel has dedicated their product development in the path of ultra-high power cells with focus.

The launch of a new generation 21700 power cell, INR-21700-P45B, featuring 7% higher capacity however 22% lower DCR compared to P42A. Its consistent 45A discharging performance has now enhanced hugely with superior fast charge capability up to 3C charging rate.

This is a starting point of low impedance version that shall be ideal for premium segment in EV, eVTOL, micro-mobility, home appliances and more applications.

Molicel Battery - Ultra-high Power Cell INR21700-P45B

Cell Voltage: Nominal: 3.6 V; Charge: 4.2 V; Discharge: 2.5 V

Typical Capacity: 4.5Ah (16.2Wh) / 4500 mAh

Charge Current: Recommended: 4.5 A (1C); Maximum: 13.5 A (3C)

Discharge Current: Continuous (MAX): 45 A

Dimensions: Diameter: 21.55mm X Length: 70.15mm

Weight: 70g

Power Output: 184W (10s, SOC 90%); 168W (10s, SOC 50%)

Energy Density: 643 Wh/l; 242 Wh/kg

ABOUT ADVANCED R&D PRODUCTS & APPLICATIONS bolt Up to 120W Higher retention for discharge energy up to 120W continuously loop 500+ Cycles High rate 80% retention electrical_services Fast Charge 13.5A continues charge south_west Lowest DCIR Max internal resistance 13.8 mOhm trending_down Low Impedance Growth Over long cycle thermostat Thermal Controlling In cell thermal distribution optimized (3-4 °C)

SKU Number: RRC01S4500

ULTRA-HIGH POWER LITHIUM-ION CELL, 4500mAh, 2S 2-Cell Pack

INR21700-P45B

Molicel has dedicated our product development in the path of ultra-high power cells with focus.

This is a starting point of low impedance version that shall be ideal for premium segment in EV, eVTOL, micro-mobility, home appliances and more applications.

Molicel Battery - Ultra-high Power Cell INR21700-P45B

Cell Voltage: Nominal: 3.6 V; Charge: 4.2 V; Discharge: 2.5 V

Typical Capacity: 4.5Ah (16.2Wh) / 4500 mAh

Charge Current: Recommended: 4.5 A (1C); Maximum: 13.5 A (3C)

Discharge Current: Continuous (MAX): 45 A

Dimensions: Diameter: 43.2mm X Length: 70.15mm

Weight: 140g

Power Output: 184W (10s, SOC 90%); 168W (10s, SOC 50%)

Energy Density: 643 Wh/l; 242 Wh/kg

Choose your custom pack from the options below, if there's a plug and wire combination not listed, type in your request in the box provide below the options. Photos depict wire configuration options, want something different, type in your request in the box provided below the options.

SKU Number: RRC02S4500

ULTRA-HIGH POWER LITHIUM-ION CELL, 4500mAh, Multi-Cell Pack (3S & Up)

INR21700-P45B

Photo shows a 2S 2-Cell Flat Pack and a single cell for reference.

Molicel has dedicated our product development in the path of ultra-high power cells with focus.

This is a starting point of low impedance version that shall be ideal for premium segment in EV, eVTOL, micro-mobility, home appliances and more applications.

Molicel Battery - Ultra-high Power Cell INR21700-P45B Single Cell

Cell Voltage: Nominal: 3.6 V; Charge: 4.2 V; Discharge: 2.5 V

Typical Capacity: 4.5Ah (16.2Wh) / 4500 mAh

Charge Current: Recommended: 4.5 A (1C); Maximum: 13.5 A (3C)

Discharge Current: Continuous (MAX): 45 A

Dimensions: Diameter: 21.55mm X Length: 70.15mm

Weight: 70g

Power Output: 184W (10s, SOC 90%); 168W (10s, SOC 50%)

Energy Density: 643 Wh/l; 242 Wh/kg

Choose your custom pack from the options below, if there's a plug and wire combination not listed, type in your request in the box provide below the options. Photos depict wire configuration options, want something different, type in your request in the box provided below the options. See Battery Configuration Chart for examples reference.

Please indicate # Cells x # Cells and other notes

in the "Battery Pack Shape Notes" box below, then in theComments section at checkout tell us you're sending us a drawing, diagram, or photo.

Some helpful shape descriptions:

Square: # Cells High x # Cells High, Even # Cells, looks like two cells on top of two cells from end view.

Block: # Cells Flat Wide x # Cells Flat High

Block Offset/Nested: # Cells Flat Wide x # Cells Flat High Offset/Nested

Double Stick: # Cells End to End beside # Cells End to End, "Shotgun barrel style"

Triangle: 3 Cells in a triangle (1 cell nested on top of 2 cells)

Triple Stick Triangle:2 Sticks of #Cells End to End + 1 Stick of # Cells High Nested, multiples of 3 Cells

Triple Stick Flat:3 Sticks # Cells x # Cells Flat, multiples of 3 Cells

Quad Stick Offset/Nested:# Cells per Stick, 2 Sticks Wide x 2 Sticks High, Offset/Nested, Even Cell Counts

SKU Number: RRC00S4500

2.4-inch color screen, 65535 colors, curve display, data statistics.
High-speed sampling, recording instant, 32-bit ARM processor, 12-bit ADC
Easy to use: The knob controls the PWM output and supplies the governor throttle signal.

Technological design, distinct edges and corners.

Supports up to 50V input, 150A maximum current.

Upgrading firmware is as easy as copying files.

WM150 SPECS

Input voltage:1-50V@MAX150A

Input: 5.0V@1A Firmware upgrade@USB3.0

USB Signal port: 1000us-2000us @50Hz

LCD display: TFT 2.4 inch 320*240 resolution

Dimensions: 80mm*54mm*23mm

Weight: 82g

SKU Number: TRCWM150

Key Features

Spektrum Smart Technology Makes Charging and Maintaining Batteries Easy
Integrated Microchip Stores Unique Parameters for Each Battery
New IC3 and IC5 Connectors are Compatible with EC3 and EC5
Save Time and Hassle, while Improving Battery Life Smart Discharge
Allows Batteries to Automatically Discharge to a Safe Voltage

Feature Overview

You'll never have to set charge preferences for a Spektrum Smart battery until you want to. When a Spektrum Smart LiPo battery is connected to a Spektrum Smart charger, unique parameters and health of that Smart LiPo battery upload from the Smart memory microchip integrated into the battery. Through the charger, you can view and set preferences, such as charge rates, so that all you have to do to charge the pack every time is press the charger "Start" button. Smart technology takes care of the rest.

Every Smart LiPo battery is factory assembled with the next-generation IC3(TM) or IC5(TM) output connector that's conveniently compatible with older devices equipped with robust EC3(TM) and EC5(TM) connectors. You can use Smart Batteries with older systems, but only when connected to a Spektrum Smart device will all the benefits of Smart technology become obvious.

Spektrum Smart LiPo Batteries Store Unique Data, such as:

Battery Brand
Battery Type
Battery Capacity
Battery C Rating
Individual Cell Voltage
Battery Temperature
Charge/Discharge Cycles

Spektrum Smart LiPo batteries also maintain an error log including the number of over-heat, over-discharge and over-charge incidents which can be helpful data in assuring that the battery you've chosen is right for the application. A Smart Battery uploads its charge parameters to a Spektrum Smart Charger automatically making charging as simple as pressing the "Start" button. The charge rate of every Smart Battery is customizable, allowing you to take full advantage of packs with faster charge ratings.

Smart Battery Technology

When connected to a Spektrum Smart charger, unique parameters and health of your Smart LiPo battery upload from the Smart memory microchip integrated into the battery. Through the charger, you can set and record preferred settings, such as charge rates and self-discharge options, so that all you have to do to charge the pack is press the "start" button. Smart technology will take care of the rest. Every Smart LiPo battery is factory assembled with the next-generation IC3(TM) and IC5(TM) output connector that utilizes a data transfer wire to relay saved information to your Smart Chargers.

Data Rich

An integrated microchip allows each Smart Battery to save vital information such as battery brand, chemistry, cell count, capacity, number of charging cycles, number of discharges, C rating, battery temperature, and internal resistance. Additionally, each battery will save a log of unhealthy events such as over-charge, over-discharge, and over-temperature. This allows you to make the most informed decision about each battery when you are getting your gear ready for a day at the field or the track.

Simple and Quick

Preset charge, discharge, and storage parameters are automatically relayed to a Spektrum Smart Charger making charging as simple as pressing the "start" button. Charge rate of individual batteries can be user customized allowing you to take full advantage of packs with faster charge ratings. The integrated microchip on each battery will remember the last charging rate you set, so the next time you plug it in, these settings will automatically populate so all you have to do is press "Start."

New IC3 & IC5 Connectors

The innovative Smart connection is made possible by an installed microchip on every battery, feeding the unique information through a data cable to the new IC3 and IC5 connectors. The IC series of connectors are designed from the ground up to provide a more solid connection, higher heat resistance, and effortless installation. For those using the popular EC3 and EC5 connectors, there's no need to worry. The IC connector series is entirely backwards compatible with existing connectors so you can use Smart Batteries with older systems, but only when connected to a Spektrum Smart device are all the benefits of Smart technology obvious.

Smart Discharge

LiPo batteries with Spektrum Smart(TM) technology practically take care of themselves. When programmed with a Spektrum Smart Charger, Smart Batteries will automatically discharge to your predetermined storage voltage when they are left to rest for a time period you choose, between 12 and 240 hours. This feature will help to extend the life of your Smart Batteries by preventing your batteries from sitting fully charged for an extended period of time, which can damage the chemical integrity of Lithium Polymer cells. This unique feature results in longer battery life expectancy and better performance over the life of the pack.

Product Specifications

Hard Case: No
Maximum Continuous Discharge Rate: 30C
Product Application: Air
Product Height: .8 in (20mm)
Application: Air
Product Weight: 200g to 299g
Roar Approved: No
Auto Storage: Yes
Product Width: 1.7 in (42mm)
Technology: Smart
Battery Voltage: 11.1V
Connector Type: IC3
Discharge: 30C
Maximum Charge Rate: 3C
Product Length: 5.5 in(140mm)
Number of Cells: 3
Smart Technology: G1 Technology
Battery Type: LiPo (3.7V per cell)
Capacity: 3200mAh
Material: Soft Case

SKU Number: SPMX32003S30

Fiberglass Reinforcing Cloth .056 Ounce. 1 SQ YD Approx. 36 x 36"

Great to use with Beacon's Foam Finish to strengthen & support foam.

Contains one square yard of Fiberglass Cloth.

SKU Number: BCNFTFRC15359

Fiberglass Reinforcing Cloth .075 Ounce. 1 SQ YD Measures Approx. 38 x 36 Inch

Material: Fiberglass
Color: Clear
Fabric Type: Cloth, woven, fiberglass
Thickness: 1.2 mils
Finish: Volan Finish Warp = 56 Fill = 56

Extremely Lightweight Fiberglass Fabric woven cloth. Wets out clear. Great for RC airplanes. Used as a surface layer or in hobby industry, commonly used on model airplanes Hobby lightweight plain weave fabric.

SKU Number: RRCFGC075X38X36

An advanced trainer that's so much fun, it's SPOOKY!

When we designed the GHOST, we envisioned a trainer that could do more than the typical boring trainer. The GHOST needed to offer you the opportunity to train, advance, and even have fun - all with the same airframe. And that's just what we've accomplished.

To start, the GHOST has been designed as an easy-to-build model with a wealth of laser-cut parts. Actually, most every part used in the GHOST's construction is already pre-cut for you out of hand-selected lite-ply and balsa woods.

The wing is a flat-bottomed airfoil which is a cinch to build using our exclusive laser-cut WEB-LOCK construction that not only gives you proper rib spacing, but also holds each rib at a true 90? to the building surface, without the need for additional tools.

The fuselage is also an easy build as we've engineered the fuselage sides with slots to lock in each former at the right spot - and angle. Also, we've integrated our Multi-Size Servo mounts into the fuselage sides which makes mounting the rudder, elevator, servos a breeze (and throttle - if using glow).

Power can come from either glow or electric powerplants and there's a large, magnetic, top hatch which gives you quick access to the batteries and/or fuel tank.

At first, the GHOST might appear to be just a Good Honest Old School Trainer. But as they say "Wait, there's more!".

Flaps are included - a first for an OSMW kit. These are quite effective and can slow the GHOST to a crawl in the air. Choose to install them during the initial build, or they can be added at any other time - even after you've flown the GHOST for a while!

The GHOST's tall and wide main gear makes taking off from paved or grass surfaces quite easy. Throttle up, and you'll find the GHOST takes to the air in a surprisingly short rollout.

At lower throttle settings, the GHOST is slow and stable in the air, making it easy for a new pilot to learn how to navigate the skies. Throttle up the GHOST a bit and you'll start to open up more capabilities, including some fun barnstorming. At even higher speeds, the GHOST can perform a surprising amount of aerobatics to wow the crowds.

And all of this with the same airframe that many would write off as "simply a trainer".

Even when the wind gets a bit gusty, the GHOST's smooth flying characteristics will give you the confidence you need. When it comes time to land, simply lower the throttle and gently glide down to the runway. Again, no surprises, which is just what you want in any design.

And after you've mastered flying the GHOST, add to it's capabilities by adding in one of our Fun Fly Bay kits (available separately). Once assembled, these kits will bolt up through the bottom of the GHOST's fuselage. Like the GHOSTS's flaps, these kits can be added (or swapped out) at any time - even after you've flown for a while. For more information on these kits, check out the right hand column.

Specifications:

Wingspan: 62 inches

Wing Area: 675 sq. inches

Length (airframe only): 42 inches

Weight: 4.5-6 pounds RTF

Radio: 4 to 6 channel (4-7 standard sized servos)

Power:

o Glow (.30-.46 glow)

o Electric (450+ watt, 60+ amp ESC, 3S to 4S LiPo)

Featuresof the GHOST:

Premium USA Hardware

Included in each Old School Model Works kit is a premium hardware package. We only source our hardware from brand-name, USA manufacturers to guarantee the best quality.

WEB-LOCK Construction:

There's nothing else like it. Build our wings, straight and true - with a minimum amount of fuss.

Front Hatch:

This top hatch gives you plenty of room to access the battery and/or fuel tank.

Flaps Included:

Flaps can be installed during the initial build, or added after you've flown for a while - your choice.

Design Your Color Scheme:

Download this sheet to design your GHOST's color scheme.OSMW GHOST COLOR SCHEME

Additional items needed to complete the GHOST kit:

o Propeller

o Engine/Motor, mount & mounting hardware

o Radio system with 4 to 7 servos (stardard-size)

o 2 "Y" servo harnesses (one for ailerons, one for flaps)

o Pushrods (28" for elevator and rudder, 9" for throttle, 6" for the ailerons and flaps)

o Clevises for the pushrods.

o Wheels: two 3" main wheels, tailwheel assembly

o Covering (typically 2 rolls - more needed for higher complexity finishes)

Make It A Combo: GHOST Fun Fly Bay Kit (Drop)

Add this optional accessory kit to your GHOST to open up your Fun Fly Bay to Drop capabilities. Once assembled, it bolts into the fuselage and gives you the ability to RESPONSIBLY drop parachute men, candy, and other fun-fly items.

o Ready to assemble kit

o 37.5" cubic inch bay capacity - 5" x 2.75" x 2.75".

o Door mechanism is protected (separated) from the bay.

o Self-contained unit that bolts into the GHOST with two bolts.

o Includes installation hardware, hinge material and door mechanism.

o Also includes 1 parachute action figure.

o Plug your servo into a spare channel and it's ready to go.

o Requires a standard-sized servo and long servo arm (not included).

Due to high demand, please allow 1-2 weeks for shipment, thank you!

SKU Number: OSMGHSTKIT

Blue high temperature silicone coupler tubing. 1 Inch ID x 1-1/8 Inch OD x 1/16 Inch (1.587mm) wall thickness. For use with tuned pipes and extending exhaust of glow powered engines. Not for use with gasoline. 11-13" section.
SKU Number: RRCCPLR1000TW

Blue high temperature silicone coupler tubing. 5/8 Inch ID x 3/4 Inch OD x 1/16 Inch (1.587mm) wall thickness. For use with tuned pipes and extending exhaust of glow powered engines. Not for use with gasoline. 11-13" section.
SKU Number: RRCCPLR0625TW

Pacer Technology (Zap) brand package of Pacer Extender Tips for CA Glue Bottles.

FEATURES:

Fits most brands of CA bottles

Dispenses smaller micro drops for more precise application

Flexible for extending into hard-to-reach areas

YOU WILL RECEIVE:

24 Pacer Extender Tips for CA Glue Bottles

REQUIREMENTS:

Placing over CA bottle opening

SPECIFICATIONS:

Length: 1.7 (43mm)

Diameter at Bottle Attachment Point: (4mm)

SKU Number: PACPT21

RRC 64 rubber bands, 1/4 lb bag. This size is the same length as the SIG #64. Perfect for wings that are a little wider like the Sig Senior and others.

Size: 3.5" Long x .25" (1/4") Wide

Weight: 1/4 lb bag

SKU Number: RRCRB0640025

RRC 105 rubber bands, 1/4 lb bag. This size is the same length as the SIG #67, at 5" Long with more width. Perfect for wings that are a little wider like the Sig Senior and others.

Size: 5" Long x .625" (5/8") Wide x .055" Thick

Weight: 1/4 lb bag

SKU Number: RRCRB1050025

Built in house with raw cells with solderable nickel tabs. Super High discharge 20C, 4.8Amp. Great little cell for sub mini indoor ships.

Lithium packs/cells require a Lithium Ion Charger rated for the correct number of cells as Ion and Polymer share the same charging method. Priced below in various configurations.

Pack Approximate Dimension: 1-1/4" Long x 1" Wide x 1-1/8" Thick

3S Pack Weight: .8oz/22.67g

Automatically comes with XH Balance Plug, Choose your balance wire length from the options.

Photo shows XT30 Yellow Plug, choose your output connector and wire length from the options.

SKU Number: RRC03S0240HD20C

We have a special stock of previously owned kits. Many classic, rare and a few modern choices. Take your pick before they are all gone. Photos here are samples, we have many more.
SKU Number: VintageKits

Check it out, more irons, more solder, more supplies than anywhere else. You need it, we have it!

MANY NEW ITEMS

Solding Irons, Jigs, Tools More quipment than the Bond women. Can you believe more than 10 different Iron choices, 40 to 300 watts.

Wick, Conductive Grease, Tip Cleaner, REAL 60/40 LEAD Solder - Choices Galore.

Surf path, column on left: Click , then within Tools you'll find along with .

Or get there quicker by following category roll down box above left.

SKU Number: SOLDERALL

The Very Best In RC Electronics, Hardware & Laser Cut Kits! (1)

NASA wants to go back to the moon.
Radical RC'sWicked Wingbeat them to it!
Check out our original designs! Radical RC Verti-Go 125, Verti-Go 3D, E-Hornet, Mini Stick, Micro Stick, Micro Bipe, Micro Low Stick, Quick Wing 12mm, Quick Wing 20mm, Quick Wing Twin 20mm Double Trouble, Das Mini Low Stick, Das Mini Bipe, Mini Hunter, Mini Intern Trainer, Stick 600,and Stick 400!Electric Flight Flight KitsThe Dayton Wingmasters

Help pages, scan the gauges while you're here:
We've Got Radical Wire
Radical RC Shameless Plugs
Battery Configuration Terminology Help Page
Battery FAQ'sRadical RC Crystal ExchangePrint our new Crystal Exchange Request Form and learn how to exchange your unwanted channels for those you can use
Read our Returns & Handy Tips for saving time and moneyRadical RC Cycler FAQ'sHow to check your cycler for accuracy
NiMH or NiCad? Charging, Your New Battery
I've been asked 1000's of times, here's your answer
Lithium Applications
Lithium Safety
Safety and Instructions!
Should I choose 4.8 or 6 volt packs?
Copy of an email I answered with all the key questions about 6 volt packs
Soldering Cells
Radical RC's help page for soldering together your own battery packs
SHIPPING FAQ'sPrivacy PolicyCustom Graphics & 3D PrintingCheck out our sister site, RC HOBBY CENTER! Check out our sister site, we offer many other products and additional services to make your life easier! Cool LinksCool and helpful links! Coming to Dayton? Includes link to nearby hotel; conversion calculator website; Dave's favorite local RC Club; AMA, and more!Orbit Repair Request FormPrint and complete this form for all Orbit Charger repair orders to be included with all repair requests.Pictured to left is one of Garrett's competition ships, to right ....
Dave, Here is a picture of my second plane. This is a 3W Extra 330 40%. The plane is flying great. Thanks so much for all your support in this hobby. I really like using your products. My friends as well are very happy with the equipment & fast-friendly service that is coming out of your company. Let's keep in touch. -Garrett Morrison

Our Address:

Logistics Prime, LLCdba Radical RC
2130 Harshman Rd
Dayton, Ohio 45424-5026

NEW Voice: 937-236-2455

Email: Sales@RadicalRC.com

Technical Help: Tech@RadicalRC.com

Where the excitement isbuilding!

The Very Best In RC Electronics, Hardware & Laser Cut Kits! (2024)

FAQs

How much does it cost to build an RC plane from scratch? ›

References